How to Add Up Dimensions in Bluebeam Review

Calibration

The Calibration section sets the certificate scale and measurement precision. To ensure the accuracy of measurements, takeoffs, and and then on, check that the calibration is prepare correctly.

Shop Calibration in Page: Select to store the scale when the file is saved. If unchecked, the page will need to be recalibrated the next time the file is opened. Scales are stored by folio; for multi-page PDFs, fix the scale for each i individually. Is unavailable if Use Embedded Calibration is disabled in Options.

Separate Vertical Calibration: Select to define separate 10 and Y scales. See Calibrating Separate X and Y Scales for more information.

Independent Units: Select to define independent units of measure for surface area and volume measurements. When selected, Area Unit and Volume Unit dropdown menus will announced. Select the desired measurement units from each. When not selected, these measurements automatically apply those established in the certificate'south calibration.

Scale definition: The current calibration is shown in the form (Measurement A) = (Measurement B). These can be changed manually, if desired, though calibration is unremarkably recommended as sometimes scaling occurs during the PDF creation process.

Precision: Defines the decimal or fractional precision of the measurement values.

Calibrate: Calibrates the document to allow accurate measurements to be taken. Run across Calibrate for more information.

Recalculate: Recalculates existing measurements after the precision or calibration has been changed.

Measurements

The Measurements section controls labels for new measurement markups and reports data that can be helpful while taking measurements.

Field of study: Defines the subject area for the selected measurement markup. If no measurement is selected, it defines the Subject field for the next measurement markup placed. Subject is reported in the Markups listing; giving like markups similar subjects can make them easier to work with in Markups listing.

Characterization: Defines the label for the selected measurement markup. If no measurement markup is selected, it defines the Label for the next measurement markup placed. The label is reported in the Markups list and appears on the markup itself past default.

Depth: Defines the depth for Book, Area, and Perimeter measurements, which is used to calculate volume and wall area. Tin be fix before placing the measurement (but afterward an applicable measurement type is selected) or subsequently selecting an existing markup.

Width: Shows the width (to calibration) of the measurement. For the certificate width, see the Layout section of the Properties tab.

Height: Shows the top (to scale) of the measurement. For the document height, see the Layout section of the Properties tab.

Slope: Describes the gradient ration for the measurement, allowing for accurate calculations of materials over a sloped plane. To set a slope, select a unit of measure out for it (Pitch, Caste, or Course) and enter the value in the respective field.

Scale: Shows the calibration of the selected measurement markup or Viewport. If none are selected, the scale of the electric current document is shown.

Current and Total columns: Shows the sums of the of the measurements taken and then far. Click Clear to reset these accumulators.

Viewports

The Viewports sections shows viewports (regions of the drawing that accept different scales than the default scale of the document) that are on the electric current document and allows y'all to create new Viewports or manipulate existing Viewports. Encounter the Viewports topic for more information most creating and manipulating Viewports.

Options

The Options sections contains other options pertaining to measurements.

Make Annotation: When checked, measurements are created as permanent annotations on the certificate. When unchecked, measurements are temporary. This part is but bachelor for Studio Session PDFs.

Snap Orthogonal: Restricts measurements to angles in 45° increments. This can exist temporarily enabled past property down SHIFT.

Snap to Content: Snaps the cursor to the underlying lines and drawing elements, making it much easier to accurately select 2 points. But snaps to vector content in a PDF file. Will not snap if the content is an prototype or a scanned file. The cursor will change to include a shaded foursquare when it is over an element that can be snapped to.

Use Embedded Scale: Applies the scale defined in the certificate when measures are created.

Highlight Viewports: Causes any Viewports on a page to be highlighted in blue anytime a measurement tool is selected.

conleyfluntence.blogspot.com

Source: https://support.bluebeam.com/online-help/revu2017/Content/RevuHelp/03--View/01--Tabs/Measurements/Measure-Tab--MV.htm

Share this post